Thursday, February 13, 2014

Articulated Streamer Pattern

A nice Oatka creek brownie taken on a black articulated streamer.
A few weeks back I had the pleasure of speaking at the Oatka Fish and Game club about my adventures in streamer fishing.It was a whole lot of fun and I had the chance to meet a whole new group of excellent fly fishermen and fly tiers. I promised them that I would post the recipe and tying instructions when I had the chance.

So here is one of the patterns I shared with them and like to fish on Oatka creek for trout, and when finished, measures in at around four inches. You may think that this is a bit extreme for such a small stream, but I have found that flies of this size actually make for better fishing.

Tossing larger flies, especially in fresh water situations like on Oatka, will give you an opportunity to move out of your comfort zone. Fishing during high water situations when stream conditions are less than perfect for dry fly fishing and spending your time on the move are prime examples. 

I also recommend using a six or seven weight rod, as it will perform much better when tossing big flies. Just think about all the false casting you would need with a lighter rod.

The articulation gives the fly some really great movement and with materials like marabou and those silly rubber legs - it is a fly that breathes.

This pattern is best fished while stripping in at ten to twelve inches at a time. And it wouldn’t hurt to open up your loop while casting and slap the fly on the water, as many trout will take the fly just as it sinks below the surface.

Kelly Galloup is perhaps the most well known fly designer when it comes to articulated flies. But there are plenty of others who have brought their own flavor to the creative world of fly design. 

Michael Schmidt of Angler’s Choice Flies,  Pat Cohen of Super Fly – Custom Fly Tying & Nick Granato of Fly Obsession are just a few of those innovative fly tyers that I like to follow.

Anyway….here it is. Kelly Gallops circus peanut.

If you are doing more than a couple of flies at once, I suggest making several back parts first before starting the front part. This will save time in the end. 

Recipe

Hooks (front & back) – I use size #4 stinger hooks or size #10 Bass Bug/popper hooks

Thread – Danville flat waxed nylon 210 denier/ UTC 140 Denier or other (color to match)

Tail (back hook only) – Marabou (color to match)

Hackle – Nice webby saddle hackle or schlappen (color to match)

Body – Woolly bugger chenille/estaz/Ice dubbing – anything that will give off a little flash is good.

Legs – Crazy legs/buggy nymph legs or anything similar (color to match)

Over wing – Marabou (color to match)

Wire - .30 or .38mm beading wire from Walmart or other craft store or Senyo’s intruder wire.

Beads – Plastic beads (color to match) Depending on the size of the bead you may only need 2, smaller beads you will need 3.

Eyes – Brass eyes/tungsten predator eyes/lead eyes (sized to match or one size heavier)



Here a few of the materials you will use.

Tie in marabou tail first (back hook only)

Tie in hackle and chenille. Coat the shank with super glue or head cement before wrapping material forward.

Wrap materials forward and then add rubber legs and marabou over-wing. Back fly is now done.

Front hook starts with a set of weighted eyes tied in upside down

Turn over hook and add in craft wire (about a 3-4 inch piece is good) and slide beads onto wire.

Feed the wire through the already finished back fly and then feed tag end of wire back through beads and secure onto front hook. Make sure to leave a nice little loop for good articulation. Trim access wire.

Tie in hackle and chenille, and then coat shank of hook with super glue or head cement before tying forward.
Wrap materials forward and add in rubber legs and marabou over-wing. And then tie in a short piece of chenille to wrap around eyes.

Wrap chenille in a figure 8 pattern around eyes and tie off. Then trim rubber legs to match the length of the hook and tail. Add some head cement and your done.

 Have fun tying this pattern. And remember you can mix and match different colors and materials to get the outcome you want.
 
Oatka brown with an olive articulated streamer.

5 comments:

Scott Feltrinelli said...

Beautiful fly Brian. Nicely done. I am going to tie a couple of those. I love using big flies on small waters.

bfly said...

Right on Scott....Good luck!!

THE RIVER DAMSEL said...

Hey hey!! This is a February post!! Time to update us... = ) Happy fishing...

THE RIVER DAMSEL said...

Hey hey!! This is a February post!! Time to update us... = ) Happy fishing...

Blogger said...

I've just downloaded iStripper, and now I enjoy having the sexiest virtual strippers on my desktop.